CROWN MA-5002VZ MACRO TECH MACROTECH 5002 MA5002 VZ

Pricing & History

Sold for
Start Free Trial or Sign In to see what it's worth.
Sold Date
Source eBay

CROWN MACRO TECH MA-5002VZ 3 AMPS AVAILABLE. ALL IN LIKE NEW CONDITION. ALL HAVE LESS THAN 100 HOURS USE ON THEM. ONE HAS LESS THAN 50 HOURS. MINT TO NEAR MINT CONDITION. 9.9 out of a 10 cosmetically. FACE AND CHASSIS ARE A+++!! NO DUST, NO RUST! NEVER SAW A LOAD BELOW 4 ohms STEREO. CAN BE PICKED UP OR SHIPPED GROUND INDIVIDUALLY, OR ALL BY FREIGHT. BUY ALL 3 UNITS AND GET A FREE SHOCK RACK AMP CASE!!! Product Description: MA-5002VZ Specifications The following applies to 120-VAC, 60-Hz units in Stereo mode with 8-ohm loads and an input sensitivity of 26-dB gain unless otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Power Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo, 4 to 16 ohms in Bridge-Mono and 1 to 4 ohms in Parallel-mono mode. Voltage Gain to 1-kHz, 8-ohm rated output; 132:1 6% or 42 dB 1 dB gain at 0.775-volt sensitivity. 71:1 12% or 37 dB 1 dB gain at 1.4-volt sensitivity. 20:1 3% or 26 dB 0.25 dB gain at the 26-dB gain setting. Required AC Mains: 50 or 60 Hz; 100-, 120-, 200-, 208-, 230-, 240-VAC (10%). AC Line Current ,Current, voltage and frequency requirements are provided on the units back panel. At Idle: All units draw 90 watts or less. AC Line Connector: 10 AWG cordset with NEMA TT30P plug is provided on 120 VAC, 60 Hz North American units. Performance Frequency Response: 0.1 dB from 20 Hz to 20 kHz at 1 watt. Phase Response: 10 degrees from 10 Hz to 20 kHz at 1 watt. Signal-to-Noise Ratio,A-weighted: Better than 105 dB below rated 1-kHz power. Total Harmonic Distortion (THD): 1-kHz rated power, 0.05% or less true THD. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.05% from rated power to 35 dB below rated power at 8 ohms. Damping Factor: Greater than 1,000 from 10 Hz to 400 Hz. Controlled Slew Rate: (Slew rates are limited to useful levels for ultrasonic/RF protection.) Greater than 30 volts per microsecond. Controls Compressor: A three-position back-panel switch is used to control each channels input compressor. The "fast" setting provides an attack time of 4 milliseconds and a release time of 300 milliseconds; the "slow" setting provides an attack time of 12 milliseconds and a release time of 600 milliseconds; the "off" setting defeats output-driven compression. Enable: A front-panel push button used to turn the amplifier on and off. Input Ground Lift: A two-position back-panel switch located on the PIP2-FXQ used to isolate the input audio signal grounds from the AC (chassis) ground. Level: A front-panel rotary potentiometer for each channel with 31 detents used to control the output level. Loudspeaker Offset Integration: A two-position back-panel switch for each channel used to turn the loudspeaker protection circuitry on and off. The circuitry protects against DC, off-center woofer cone movement, and unwanted subsonic and ultrasonic frequencies. Sensitivity: A three-position back-panel switch for each channel used to select input sensitivity: 0.775 volts or 1.4 volts for standard 1-kHz power, or a 26 dB voltage gain. Stereo/Mono: A three-position back-panel switch used to select Stereo, Bridge-Mono or Parallel-Mono mode. VZ Mode: A four-position switch for each channel inside the front panel used to control the switching mode of the VZ power supplies. IndicatorsEnable: An amber front-panel LED that shows the on/off status of the low-voltage power supply. Signal/IOC: A green front-panel LED for each channel that flashes to show amplifier output. If a channels output waveform differs from its input by 0.05% or more, the indicator flashes brightly to show distortion. ODEP: An amber front panel LED for each channel that shows thermal-dynamic energy reserve. Normally, each ODEP indicator is lit to show available reserv... read more

Items in the Price Guide are obtained exclusively from licensors and partners solely for our members’ research needs.

Flag item for content or copyright

If this item contains incorrect or inappropriate information please contact us here to flag it for review.

If you are the originator/copyright holder of this photo/item and would prefer it be excluded from our community, contact us here for removal.