These are Brand New MC 60 treadmill motor controllers. Use them to replace broken or old controllers on treadmills. They also make great PWM variable speed controls for DC motors which can be used on lathes, mills, drill presses and any other device that needs a variable speed controlled DC motor.
To use on a treadmill:
This controller is used on ProForm, Reebok, Image, Weslo, HealthRider, and Nordic Track treadmills. It may fit other models also. It is the MC-60 controller.
DRTL49220 - PROFORM CROSSWALK 380X TREADMILL DTL32940 - PROFORM X-WLK PERFORMANCE DTL32941 - PROFORM X-WLK PERFORMANCE DTL33940 - PROFORM PF,CROSSTRAINER ULTIMATE DTL33941 - PF,CROSSTRAINER ULTIMATE HRTL393050 - HEALTHRIDER H 150i ICTL39522 - IMAGE 10.0 TREADMILL IMTL39520 - IMAGE 10.0 IMTL39521 - IMAGE 10.0 TREADMILL IMTL39522 - IMAGE 10.0 TREADMILL IMTL39523 - IMAGE 10.0 TREADMILL IMTL39524 - IMAGE 10.0 TREADMILL IMTL39525 - IMAGE 10.0 TREADMILL IMTL39526 - IMAGE 10.0 TREADMILL IMTL39620 - IMAGE 10.0 TREADMILL PCTL29320 - PROFORM C42 TREADMILL PCTL39120 - PROFORM CROSSWALK 325 TREADMILL PCTL49820 - PROFORM 380I TREADMILL PCTL93040 - PROFORM CROSSWALK 380 X TREADMILL PCTL93240 - PROFORM 350S CROSSTRAINER TREADMILL PFTL31130 - PROFORM CROSSWALK 330 TREADMILL PFTL311340 - PROFORM X-WLK TS-3 TREADMILL PFTL312040 - PROFORM LX470 TREADMILL PFTL31330 - PROFORM 325i TREADMILL PFTL31331 - PROFORM 325i PFTL313340 - PROFORM 3.0 MX TREADMILL PFTL39020 - PROFORM LX 360 TREADMILL PFTL49020 - PROFORM 380 PFTL49820 - PROFORM 380i TREADMILL PFTL49821 - PROFORM 380i TREADMILL WCTL39320 - WESLO CADENCE C62 TREADMILL WLTL35520 - WESLO CADENCE 450 TREADMILL WLTL393040 - WESLO CADENCE C72 TREADMILL WLTL393041 - WESLO CADENCE C72 TREADMILL WLTL39320 - WESLO CADENCE C62 TREADMILL WLTL39321 - WESLO CADENCE C62 TREADMILL WLTL39323 - CADENCE C62 WLTL39324 - CADENCE C62 WLTL39325 - WESLO CADENCE C62 TREADMILL WLTL39326 - CADENCE C62 WMTL31130 - WESLO CADENCE X390 TREADMILL 293030 - PROFORM 320X 293040 - PROFORM CROSSWALK 380X TREADMILL 293041 - PROFORM CROSSWALK 380X TREADMILL 293330 - PROFORM 330X 294030 - PROFORM X-WLK 345s 294031 - PROFORM X-WLK 345s 294230 - PROFORM 350s CROSSTRAINER 294231 - PROFORM 350s CROSSTRAINERTo use as a speed control on a DC motor:
(1) Look at picture #2 to see w all the connections go.
(2) You will need to purchase a 5 Kilo Ohm potentiometer (3 dollars at Radio Shack).
(3) Wire everything up. I can e-mail you a wiring diagram if necessary but it is very easy to make the connections. If you have any problems just send me a message through ebay and I will be glad to help.
(4) Connect your DC motor to the speed control (see photo). The speed control outputs 130 volts DC at 8 amps. continuously. These means you should use a DC motor that takes 130 volts DC or more. (If it takes more than 130 VDC it will just spin slower. For example, if you use a DC motor that is made for 260 VDC.... it will just operate at half power/half rpm's.) Treadmill motors work great and I can sell you a brand new 1 horsepower one for 85 dollars with shipping included.
Lastly, do not use a DC motor that draws much more than 8 amps as it may overheat the speed control.
is some additional technical information on the speed control. Some of you may find it useful, but for most it is not necessary to know. Most people will just need to pull out their old unit and replace it with the new one.
These SCR motor controllers are physically identical. The only difference is in the components used to allow a
higher Current Limit on the MC-64 and a lower Current Limit on the MC-67. The MC-60M controller is a variation of the MC-60 controller that allows a single wire harness to carry signals between the console and controller. The treadmill’s reed switch plugs into the controller, then the tach signal from the reed switch and the speed control signal are sent t...
Items in the Worthopedia are obtained exclusively from licensors and partners solely for our members’ research needs.